Make a Hidden Bail

by Judy Larson

Category: Metalwork
Technique(s): Butane Torch Techniques
Skill Level: Intermediate

A hidden bail works well when a visible attached bail will detract from the design of a pendant, or when you just can't decide how to put a bail on. They are very easy to make and attach on a flat backed pendant. Just make sure that easy solder is not used on any part of the piece before attaching the bail.

Materials

22 Gauge Dead Soft Argentium Silver Sheet - 6 Inches

H19-22SM6

Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 1 Inch
Price: $61.68
Gold Club Price: $46.26

Add to Bag

24 Gauge Dead Soft Fine Silver Sheet - 6 Inches

H9-24SM6

Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 1 Inch
Price: $48.75
Gold Club Price: $36.56

Add to Bag

Add All Items to Cart

Tools

6 Step Barrel Plier - Pack of 1

G2-503

G2-503
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $18.95
Gold Club Price: $14.21

Add to Bag

adjustable scribe

Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each

Metal Cutting Shears

SHR-536.00

SHR-536.00
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $14.97
Gold Club Price: $11.23

Add to Bag

Miniature Digital Caliper

GAU-178.00

GAU-178.00
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $39.95
Gold Club Price: $29.96

Add to Bag

Xuron Flush Cutter - Pack of 1

G2-504

G2-504
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $29.95
Gold Club Price: $22.46

Add to Bag

Premium Steel Bench Block 2 1/2 X 2 1/2

G17-9

G17-9
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $15.97
Gold Club Price: $11.98

Add to Bag

Blazer Big Buddy Turbo Torch, White

TRCH-8012

TRCH-8012
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $40.00
Gold Club Price: $30.00

Add to Bag

Medium Rawhide Hammer 1 1/4 inch - Pack of 1

G3-7

G3-7
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $32.95
Gold Club Price: $24.71

Add to Bag

7 Annealing Pan with Pumice

SOL-520.00

SOL-520.00
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $36.97
Gold Club Price: $27.73

Out of Stock

Add All Items to Cart

Instructions

Step 1

Read through the tutorial before starting the project. Follow all safety precautions pertaining to the tools and supplies being used and the area you are working in.
This stone from Indonesia with what looked like blue flames rising out of the top of a mountain on a dark night was chosen for a pendant by my daughter-in-law. I would have liked to make a larger flame at the top of the stone and use a larger blue cab, but was limited by the size and gauge of silver sheet I had on hand as well as the color of all my blue cabochons-none matched. In the end, a smaller flame was used as well as a dyed agate bead in a hand-made tube. As always, use what you have.
After finishing the pendant except for securing the stones in place, choose the chain that will be used with the pendant. Since both these chains worked well, the wider of the two was chosen to use for measurements in Step 4.

Judy Larson's Make a Hidden Bail - , Metalwork, Butane Torch, Soldering, Solder, hidden bail

Step 2

Adjust a scribe to the desired width of the bail in the area the bail will be placed. Use the scribe to scratch a line along a straight edge of a piece of metal. I had a small piece of 24 gauge sheet, which will work, but do not use anything thinner.

Step 3

Use metal shears or a saw to cut the metal strip on the scribed line. Flatten the strip on a bench block and straighten it if needed. Use an ultra fine point retractable Sharpie to mark the strip with the metal gauge and the word "BAIL" so it can be used again on a later project.

Step 4

Using a caliper, measure the width of the widest/thickest chain that the pendant will be worn on. Using that measurement, check to see which barrel will be the best, tightest fit, knowing that the metal strip will not form tightly around the barrels of either the small Wrap-N-Tap or 6 step barrel pliers. Parallel jaw pliers would be the best to use to make the bail, but use what you have.

Step 5

The pendant on the left will only be worn on an omega which is a flat chain, while the one on the right can be worn on a thicker, more round chain as well as the thinner omega. Form the wire strip around the plier barrel chosen in Step 4. Wrap only half way around if a less deep bail is needed such as the left pendant in the photo, and more than half way around if a deeper bail is desired, as on the right pendant in the photo.

Step 6

Remove the shaped strip from the pliers. Use an ultra fine point retractable Sharpie to mark a general area of where to cut the curved portion from the strip. Use heavy duty flush cutters to cut on or as close to the line as possible. If excess metal needs to be cut away, trim again with the flush cutters.

Pro Tip: Try not to use metal shears in this step. The cut edge will likely curve and it will be difficult to make it flat again without marring it.

Step 7

Place sandpaper on a bench block or other completely flat surface. Sand the cut edges of the bail completely flat, checking the fit over the desired chain periodically. Sand the sides of the bail flat as well. Check the fit of the bail on the pendant. If needed, sand again to adjust the fit.

Step 8

Place small dots of easy paste solder inside the bottom edges of the bail.

Step 9

Press the pendant front side down into pumice in a rotating pan. The pumice will help protect thinner metal, such as the flame bezel wire on this pendant, as well as any fine embellishments that may have been attached. Heat until the solder flows. Hint: For easier cleanup, the rotating pan is placed on a very inexpensive aluminum bar pan that will catch errant pumice pieces when I move things around.

Step 10

Continue as you normally would. Pickle, rinse, and dry the piece. Patina if desired. Set the stones in place

Reviews

Judy Larson

My philosophy has always been "I will never live long enough to learn everything I want to learn, go everywhere I want to go and see everything I want to see!" So, what I make and how I create it is always changing and evolving. I was born shortly after WWII to parents who grew up during the Depression. They always had a "we can do it, we can make it" attitude which rubbed off on my two younger brothers and me. My brothers are amazing and can make and do ANYTHING! When I was a little girl, my mother gave me an old carved cigar box, which I cherish, filled with pop beads, wooden beads and yarn for stringing. That was the beginning of my jewelry making journey.

On a visit to the Grand Canyon when I was a young woman, I was fortunate enough to help a Native American silversmith sand cast my first silver bracelet and bezel set a large turquoise nugget on top. I was in love, hook, line and sinker! While working full time and having a family here in northern Minnesota, my artistic endeavors slowed down but never stopped. I am an artist, scrapbooker, seamstress, woodworker and jewelry artisan. Now that I am retired, I am able to indulge in all my hobbies. However, there just never seems to be enough time in the day to do it all, but I try!

I have been teaching community education beginner and intermediate jewelry making classes since my retirement. Many of my students have been bitten so hard by the jewelry making bug that they say I have turned them into monsters-they just can't get enough. Making jewelry, seeing something take shape from small bits and pieces, is so rewarding that I hope it brings out the "monster" in you, too!