Jewelry Making

Supplies

Daily Deal
Beads
Cabochons
Cameos
Chains
Displays and Packaging
DVDs
Findings
Gemstones
Jewelry Books
Jewelry Supply Kits
Metal Sheet and Blanks
Pearls
Swarovski Crystal Beads
Tools
Wire
Clearance Items
Gift Certificates

Testimonials

"I have learned a lot and am amazed at how easy a concept this is!"

- Rob

Read more testimonials here Read More Testimonials Here


Follow Us

Follow Wire-Sculpture.com on Twitter! Join the Wire-Sculpture.com Facebook Fan Page!

Tree of Life

Tree of Life

Designed by Albina Manning

Skill Level: Beginner/All

Technique: Coiling and Pendant Forming

The Tree of Life is an esoteric philosophy common to many cultures and mythologies. The Ancients envisioned the entire cosmos in the form of a tree, whose roots grow deep in the ground, branches reaching high into the heavens. You can choose different colored gemstone chips to create your tree according to a favorite season, such as amber and jaspers for autumn; or aventurine with sprinkles of rose quartz to represent a blossoming tree in spring.

Materials

Tools

Formula

Circumference of dowel + 2-inches = length of 16g wire

Instructions

  1. Measure the distance around the dowel and cut a piece of 16ga wire according to the Formula. From each end, measure 1-inch and mark. Use flat-nose pliers at each mark, to bend the wire out at a 90° angle (each bend toward the same side).
    Tree of Life
    Line Break

  2. Working from the wire-coil and leaving a 1-inch tail, use the 24g round wire to tightly coil, from one angle just made, down the entire length of the 16g wire, to the other angle. Do NOT cut this coiling wire! (The entire length of 16g wire should be covered with one continuous coil, between the angles.)
    Tip: I prefer coiling the wire by holding the one-inch "handle" and turning it in a circle while gripping 24ga wire with 16ga base between index and thumb.
    Tree of Life
    Line Break

  3. Using the item chosen as the pendant size, carefully shape the coiled wire around it, until the two angled ends meet.
    Tree of Life
    Line Break

  4. Leaving ¼-inch, cut the short tail of 24ga wire. Place the two 1-inch angled ends together, measure from the ends toward the circle 1/4-inch and mark. Hide ¼-inch 24g tail between them, and use the 24g wire still attached to begin coiling both of the angled wires together (which will become the bail). Continue until the coil reaches the 1/4-inch marks. Do NOT cut the 24g wire yet!
    Tree of Life
    Tree of Life
    Line Break

  5. Slightly bend the bail toward the front and then, using any cylindrical device, (mandrel, bail pliers, pencil, etc) form the bail toward the back. Secure the bail by wrapping around the entire group of 4 bail wires, three times with the 24g wire still attached. Then wrap a couple times around the back of the bail and finally, trim the 24g wire.
    Tree of Life
    Tree of Life
    Line Break

  6. Cut 4 pieces of 24ga wire 9-inches long (22.5cm) and 1 piece 12-inches long (30cm). Fold a 9-inch wire in half and place it in the middle of the circle's bottom (frame). Very carefully pull the wire ends so folded wire will 'hide' between coils.
    Tree of Life
    Line Break

  7. Coil the 9-inch wire ends 2 times on each side, so each wrap lies between frame's coils.
    Tree of Life
    Line Break

  8. Continue attaching the remaining 9-inch pieces of wire in the same manner, placing them so the distance between each is the same.
    Tree of Life
    Line Break

  9. When attaching the 12-inch piece, fold it so that one end is just 4-inches long. This 4-inch section has to be on the inside, while the longest tail will be outside (red arrow).
    Tree of Life
    Line Break

  10. Lift all 10 tails up, gathering them in a pinching fashion. In this step you designate the length of tree's roots and where the trunk will begin.
    Tree of Life
    Line Break

  11. Create the trunk by using the longest tail (from step 11) to begin wrapping all 9 wires together. Wrap 8-10 times to show (or more if desired).
    Tree of Life
    Line Break

  12. Separate all 10 wires into pairs as shown. Create each individual branch by twisting each pair together 4-5 times.
    Tree of Life
    Tree of Life
    Line Break

  13. Add foliage to the tree by threading the gem chips and beads to each 'twig'. Place the wire with 'leaves' over the frame and wrap the wire tail 3 times around the frame. Trim the wire tail on the back of the frame.
    Tree of Life
    Tree of Life
    Tree of Life
    Line Break

  14. Continue adding leaves and securing the 'twigs' to the frame until all branches have been anchored.
    Tree of Life
    Line Break

  15. Use chain-nose and flat-nose pliers to shape the roots.
    Tree of Life
    Tree of Life
    Line Break


Check it out! Free Wire Jewelry Patterns

Did you find this pattern through a link from a friend? This Free Wire Jewelry Pattern is just one of dozens of free wire jewelry patterns we send via email. Get patterns like this one straight to your inbox - click here!